I've actually had two Cobra builds underway, one a GD and the other a lesser known Fujimi RS-5 427. The latter is generally a quicker build and only took a couple of months!
Overview
Wednesday, 31 May 2017
Engine Update 5
Now that the engine and gearbox have been coupled together it was time to deliver it to GD, they need it in order to fabricate the mounts for the chassis.
The 20th May was the GD open day at their new premises in Grantham so I seized the opportunity and loaded the powertrain in to a borrowed trailer and headed up.
It was a great turnout and fabulous day despite the heavy downpours and the engine was unloaded without issue. I was pleasantly surprised to find most people very interested in my choices rather than the shunning I was expecting for not using an American V8!
I still have to reconnect the loom to the various ECU plugs but that can be done when I get it back along with the chassis, hopefully in a couple of months.
It was also great to meet a few new people, some of which I had already chatted with online but great to put a face to a name.
Friday, 10 March 2017
Engine Update 4
So I finally received my adapter plate & pilot bearing reducing sleeve (SWR Motorsport) and clutch & flywheel (TTV Racing) so I could bolt the two together.
I had trouble getting accurate readings while clocking the bellhousing however the gearbox did slide on easily. Even though, I've ordered another DTI so will likely do it again just to be sure.
There's a lot of bolt on, bolt off activity to set this all up but I got there eventually. The bearing sleeve was used as the TKO pilot bush was too small for the 1UZ crankshaft, it's a tight fit so was put in the freezer the night before and then fitted with a dab of Loctite 272 in to the end of the crank. The pilot bush just slots inside this.
Next the flywheel was bolted on with new ARP bolts and torqued up as per ARPs instructions. The clutch pressure plate, bell housing and adapter plate were temporarily installed so I could measure the distance from the gearbox mating face to the pressure plate fingers. This measurement was then used to set the adjustment of the Tilton hydraulic release bearing.
Next the bellhousing came of, pressure plate removed and bellhousing refitted complete with adapter so I could clock it in. The opening in the adapter is quite small so I struggled to get the DTI lined up properly so I will probably have to repeat this step once I get a different DTI.
With the bellhousing back off again I could assemble and align the clutch. My alignment tool needed a few wraps of tape to get the right fit but was pretty straightforward.
The bellhousing was then bolted to the gearbox and the clutch release was slid over the input shaft bearing retainer. This release bearing requires one of the bearing retainer bolts to be replaced with a pin which stop the bearing from spinning. The release bearing position can be adjust by screwing it in or out on its own sleeve. There are two hoses which need to exit the bellhousing so holes were drilled foe these, although they may have ended up too close to the exhaust!
With a bit of graphite grease applied to the splines, I could now mate the engine and gearbox together. The engine was on the hoist and the gearbox on its stand (old office chair) so a sexond pair of hands was needed to keep everything steady but it all slid together remarkably easily.
I will be taking the assembly up to GD at the beginning of April so they can make up the engine mounts with a view to hopefully picking up the chassis at the GD open day on 20th May, fingers crossed.
Friday, 3 February 2017
Engine Update 3
The engine has been stripped down externally, all the parts media blasted and painted. As the outside of the car is loud I decided to be a bit more restrained with the engine colour scheme using a matt black and graphite grey two tone, the only orange parts so far are the fuel rails.
I stripped the original Lexus wiring loom to its bare neceasities and have begun rerouting and sleeving the loom completely. I can't go much further with that until I have the gearbox mounted and decided on the oil temperature, oil pressure and MAF sensor locations.
With regards to the gearbox, I have ordered the following:
1. Adapter plate - Ford TKO to Lexus bellhousing (SWR Motorsport)
2. Reducing sleeve to fit TKO pilot bush in 1UZ crank (SWR Motorsport)
3. Custom flywheel and clutch (TTV Racing)
4. Tilton 6102 concentric clutch slave cylinder (from Jegs in USA)
5. ARP flywheel bolts
The above should allow me to finally connect the engine to the gearbox and finish the wiring loom. Then I can cart the lot off up to GD so they can design the mounts to fit it in the chassis.
Sunday, 1 January 2017
Engine Update 2
It's been quite a while since my last post and progress has been slow of late, but has still be moving along steadily. Not much has happened with the body as I have been concentrating on the engine and drive train, there are two major challenges with this:
Engine Wiring Loom
To cut a long story short, I managed to compile a comprehensive list of pin outs for my ECU using a selection of wiring diagrams from various sources (some in Japanese!).
This allowed me to strip out all the unnecessary wiring (power steering, traction control, ABS, aircon, auto gearbox etc) and install a few relays.
I was then able to start it up on the hoist to prove everything; especially the OEM Lexus immobiliser, was working. Voila, it worked and sounded fabulous with out any exhaust fitted, I needed ear defenders!
The loom will be tidied up and rerouted once the engine goes back together.
Manual Gearbox
As I mentioned in a previous post, the Lexus UZ family of engines were never available with a manual gearbox so there is no direct bolt on replacement for the 5 speed Auto. Although briefly considering keeping the Auto and making it 'Flappy Paddle', I have decided I will have to vet a machine shop make an adapter plate.
There are already some off the shelf adapters for BMW and Toyota gearboxes, but the ratios don't suit the final drive so I have opted for a TKO600 instead. A man called Roger; formally of Thor Racing, but now of SJ Performance Engineering has a lot of experience with these engines and is the only person I can find to has mated a 1UZ to a Tremec gearbox before so I'll be catching up with him on Tuesday.
With the wiring loom removed I now started stripping the rest of the engine for cleaning and painting, I'm not going to bother with the internals so the heads will stay put for now but pretty much everything else has come off including timing belt and water pump which will be replaced.
Tuesday, 20 September 2016
Engine Update
I was originally planning on using an LS3 with T56 Magnum 6 speed gearbox but as the cost of this combination is around £10K I started exploring other options.
Although there seem to be plenty of small block Chevy and Ford engines available I want a modern engine so started looking at Audi, BMW, Jaguar/Range Rover and Lexus.
The 4.2 Audi V8s are plentiful but trying to find a suitable RWD gearbox is near impossible, I did briefly consider building a Quattro Cobra but shelved the idea.
BMW M62 engines are also affordable but I have heard that wiring them is very difficult so decided against that.
Jaguar and Range Rover engines are also readily available but do get quite expensive if looking for power.
So that leaves Lexus. The 1UZ-FE engine is found in LS400 and SC400 UK registered cars from 1991 - around 2000 and whole cars can be picked up cheaply. The pre-95 cars had stronger conrodssoncan handle a lot of power without modification and the 98 on engines received VVTi which bumped the power up from 260bhp to 280bhp and increased fuel economy.
I managed to buy a low mileage (127K) 1998 LS400 with current MOT for £550, so it comes with the VVTi engine and 5 speed auto. Having an MOT meant I could give it a good shake down on the run home and it ran like a dream.
Another bargain I found was a M112 suoercharger which I got for £300. It came off a Jaguar X350 4.2 and they even threw in chargecoolers for free. I'll probably put it through the IVA in standard form then shoe horn the Supercharger on afterwards.
These engines are known to be extremely strong and reliable but only ever came with auto boxes, however do get transplanted in to lots of drift cars so it is possible to convert them. I plan on either using a BMW 6 speed or a Supra Turbo 5 speed by means of an adapter plate and bespoke flywheel.
1st 2nd 3rd 4th 5th 6th
BMW ZF-S6-37 4.35 2.45 1.68 1.23 1.00 0.85
Supra R154 3.25 1.96 1.31 1.00 0.75
The Supra gear ratios seem preferable with the GD Euro rear diff but the BMW gearbox is cheaper, more available and known to be very strong so the dury is still out on this one. There's also the issue of IVA/DVLA and the 'one major reconditioned part' statement which might force me to buy a brand new box. If that's the case, I might go for the T56 after all.
Tuesday, 23 August 2016
No More Bling
I never really wanted a Cobra with loads of shiny Chrome as I'm trying to build a modern alternative, but didn't think there was any other option for certain things such as the windscreen so just settled for it.
After recent discussions with fellow builders, I have decided I am going to go 'bling free' after all. The chrome/shiny bits I already have are:
- Windscreen frame and stanchions
- Fuel filler cap
- Headlight surrounds
- Wiper spindle ferrules
- Wiper arms and blades
The wiper arms and blades haven't been fitted so I will see if I can return them to GD and I'll buy black ones, I think Classic Mini ones fit.
I have made enquiries with a few local powder coaters and the consensus it that Chrome can be coated after being shot blasted to ensure good adhesion, and cheaper than I was expecting too.
I now needed to remove bits from the car, the headlight surround and wiper spindle ferrules just unbolt and the Aston filler cap needs a couple of roll pins knocking out but the tricky bit was the windscreen.
The powder coating process involves oven baking which isn't good for the rubber seals which meant the glass had to be removed and after speaking with Brasscraft (they make all the UK Cobra screens) I was assured it was possible.
The frame is made of two sections, the lower bit that sits across the scuttle and the rest. These are held together by 2 flat head screws at the bottom of each side. A sharp flat object needs to be run around between the seals and the glass, I used a 6" steel ruler. I then used a flat head screwdriver to prise the lower corners apart, I could then gradually ease the two sections apart.
The top frame is more difficult as it wraps around 3 side so there is more friction in the seals, I had to resort to a nylon faced mallet here! Whilst holding the glass, I lightly tapped the corner of the frame outwards each side, then upwards from the bottom.
This process was repeated gradually each side until I could pull the frame off the glass, thankfully with everything still in one piece. Now the seals can be removed for reuse when it all goes back together.


