Overview

This blog is intended to document the build of my Gardner Douglas Mk4 Cobra; partly as IVA evidence, bit primarily to help others learn from my mistakes and/or successes.

I will endeavour to post as often as possible, with a view to entering a single post for a particular element of the build process, however inevitably some things may not be completed in one go. All posts will be tagged so it should be easy enough to find the information you seek.

Please subscribe to receive emailed updates and feel free to post any comments or questions which I will make my best efforts to respond to.
Showing posts with label Fuel system. Show all posts
Showing posts with label Fuel system. Show all posts

Saturday, 2 September 2017

Fuel lines pt1

Fuel Line
The fuel line is the bigger diameter pipe in the kit and comes coiled up with a 90 degree bend at one end, this bend goes at the front.  I carefully uncoiled the pipe, you can buy pipe straighteners but I found pulling on one end whilst a friend holds the other does the job perfectly well.

The pipe runs along the left hand top chassis rail to just behind the body mount, then dips down slightly to avoid the handbrake cables, over the front diff mount before doing an 'S' bend outboard and over the driveshaft.  I drilled and tapped the frame to secure the pipe with 'P' clips, adding a little grease in the holes to hopefully stop corrosion.

90 degree bend approximately 25mm in front of cross member

Routed along right left hand top chassis rail...

...slight downward bend rear of body mount...
...over front diff mounting plate...



...'S' bend outboard and over left hand driveshaft.

Tuesday, 23 August 2016

No More Bling

I never really wanted a Cobra with loads of shiny Chrome as I'm trying to build a modern alternative, but didn't think there was any other option for certain things such as the windscreen so just settled for it.

After recent discussions with fellow builders, I have decided I am going to go 'bling free' after all. The chrome/shiny bits I already have are:
- Windscreen frame and stanchions
- Fuel filler cap
- Headlight surrounds
- Wiper spindle ferrules
- Wiper arms and blades

The wiper arms and blades haven't been fitted so I will see if I can return them to GD and I'll buy black ones, I think Classic Mini ones fit.

I have made enquiries with a few local powder coaters and the consensus it that Chrome can be coated after being shot blasted to ensure good adhesion, and cheaper than I was expecting too.

I now needed to remove bits from the car, the headlight surround and wiper spindle ferrules just unbolt and the Aston filler cap needs a couple of roll pins knocking out but the tricky bit was the windscreen.

The powder coating process involves oven baking which isn't good for the rubber seals which meant the glass had to be removed and after speaking with Brasscraft (they make all the UK Cobra screens) I was assured it was possible.

The frame is made of two sections, the lower bit that sits across the scuttle and the rest. These are held together by 2 flat head screws at the bottom of each side. A sharp flat object needs to be run around between the seals and the glass, I used a 6" steel ruler. I then used a flat head screwdriver to prise the lower corners apart, I could then gradually ease the two sections apart.

The top frame is more difficult as it wraps around 3 side so there is more friction in the seals, I had to resort to a nylon faced mallet here! Whilst holding the glass, I lightly tapped the corner of the frame outwards each side, then upwards from the bottom.

This process was repeated gradually each side until I could pull the frame off the glass, thankfully with everything still in one piece. Now the seals can be removed for reuse when it all goes back together.

Two roll pins for the hinge and catch removed with a hammer and punch

Glass removing tools! 

This shows the two screw holes at the lower edge on each side. I'd already removed the lower frame before I remembered to take pictures. 

Prising the seal off the glass, a Stanley blade would probably have been better in hindsight. 

Two parts of the frame ready for the powder coaters 

Saturday, 20 August 2016

Fuel Filler Cap

I actually fitted the fuel filler a while ago but never wrote it up.  GD offer 2 types of filler, Aston Style and flush fit, I went for the Aston style.  This is a decision that needs to be made at the body order stage as the relevant recess need to be bonded in place.

The first thing to do was rub down and polish the fuel filler recess, this was done by hand due to the confines of it.  The centre of the mounting surface was found and an 76mm hole was cut with a holesaw.  

The Aston filler cap comes in two parts, the threaded flange and the cap itself.  The two parts were separated and the flange bolt holes drilled to 5mm (these were already pre-marked on the underside) and countersunk.  With the flange held in position on the car I then drilled through for one of the mounting holes, then bolted it in place to drill the rest.  The flange was then removed again to make the gasket.

I used countersunk Allen head bolts, but you could use button heads.

I bought a large roll of 1mm thick rubber gasket material off ebay along with a tool to cut circles (basically a compass with a blade attached) and some punches for the bolt holes.  I then made my gasket at 135mm diameter with a 76mm diameter hole in the middle, remember to cut the outer dimension first otherwise you'll have no centre left for your compass point!  With the ring made I placed it on the car under the flange and marked bolt holes which were then punched out.  I used an M6 punch just to give a bit of wiggle room for the bolts.


Gasket cutting made easy with cheap tool (left)
Bolt holes punched and gasket offered up (right)

The flange and gasket were then bolted to the car and the cap screwed on.  Initially it didn't tighten up in the right place.  The cap comes with several shims, the thicker red ones are 1mm think and the thinner blue ones 0.4mm thick.  After some experimentation I needed the 3 thick ones to get the cap to sit in the desired position.

Bolted on to car, looking lovely (although I may still get it powder coated black yet....)